The Tartan 34-2 (1984-1989)
A Source for information on Tartan Yachts model 34-2
  • Tartan 34-2 Home Page
  • All about the Tartan 34-2
    • FAQ on the T34-2 >
      • Performance Calculations
      • Production Differences
      • About the Scheel Keel
    • 34-2 1985 Brochure & Photos >
      • 34-2 Exterior
      • 34-2 Interior
    • 34-2 1986-89 Brochure
    • Original T34-2 Manual
  • T34-2 Owners Pages
    • Hull #3 - "Ocean Razor"
    • Hull #4 "Carpe Diem"
    • Hull #9 - "Temptation"
    • Hull #11 - "Bad in Plaid"
    • Hull #12 - "Bellwether"
    • Hull #22 - "Rose Claire"
    • Hull #23 -- Scarlett
    • Hull #24 - "Liberty"
    • Hull #30 - "Further"
    • Hull # 37 "Logged Out"
    • Hull #39 - "First Rate"
    • Hull #49 - "Scot Free"
    • Hull #54 -- "Sea Panda"
    • Hull #57 - "Yankee"
    • Hull #66-"Emme Anne"
    • Hull #67 - "Liberty" >
      • Offshore Experience >
        • Offshore Photo Gallery
    • Hull #70 - "Aurora"
    • Hull #75 - "O-Sheet!"
    • Hull #78 - "Kickin' Back"
    • Hull #83 - "Dash"
    • Hull #84 - "Triton"
    • Hull #88 - "Windswept"
    • Hull #94 - "Spirit"
    • Hull #95 - "Windward"
    • Hull #101 - "Athena"
    • Hull #109 - "Counterpoint"
  • Hull #9 "Temptation"
    • Temptation Travels the Great Lakes
  • T34-2 Blog

Prepping for a cruise (by Dan Wallace)

3/30/2011

6 Comments

 
The following modifications were made to go off-shore:
  • Added a SSB and antenna (the split lead clip on type)
  • Added refrigeration
  • Converted from natural gas to propane
  • Installed a macerator
  • Replaced the anchor roller with a custom made twin roller
    Put on new anchors and chain
    Newest and biggest electronics I could afford

  • The slotted aluminum toerail was a very useful tool.

    I did most of the work of installing and aligning the equipment on the boat.
6 Comments

Do you need a backstay adjuster? (by Dan Wallace)

3/30/2011

3 Comments

 
Regarding a backstay adjuster, it certainly helps to be able to twist the sail for that added ounce of speed. Having said that, it really depends on the type of sailing you prefer. If you decide to get one then definitely go hydraulic as I don't think you'll get much us from a manual. Of course if you are going to get a backstay adjuster then the corresponding forestay adjuster comes in handy.
3 Comments

Bleeding Fuel Lines and Checking Oils (by Dan Wallace)

3/30/2011

1 Comment

 
The 3GM30F diesel is a 3 cylinder Yanmar located under the companion way ladder. The way to get to it is to take the ladder off by sliding it up and lay it on the settee or something out of the way. There is a latch at the back of the engine cover, unclip it. Then pull it back and lift it up for a second. You kind of have to bump over some coolant lines but then it comes straight out. Just slide the engine cover straight back into the main salon area. You have complete access to all four sides. Behind the Nav Station is the 3/4 berth. The top of the berth is the cockpit floor. To get to the transmission, stuffing box, and shaft is very easy.. the trick to it is how much stuff is on top of the access! haha You have to move everything and lift the cushion directly behind the engine to get the board out to get too them. Just slide it back unto the aft board. The after board is removable to get to the shaft seal. This is a great area to put beer and such.  The batteries (2 deep cycle 110's and a starting battery) are under the Navstation seat on the outboard side. The water intake (and ball valve) are in the compartment aft of that.

The biggest thing you will need to do with the engine is to bleed the air out if you run out of fuel. If there is air in the fuel system, the motor will not start no matter how much you try. You will kill the batteries. Bleed it and it will fire right up. At the front of the engine on the left side as you look at it, there is a gray metal fuel jar. On the top of it is a bolt. Look aft and you will see a little lever, that’s the manual fuel pump lever. Crack the bolt open a bit and pump that lever til fuel comes out of the bolthead with no bubbles. Tighten the bolthead up while pumping the lever. Then follow the fuel lines up toward the top of the engine. There is a little bolt with a Phillips head where the lines split into 3 metal lines. Use the big screwdriver to crack that open and pump the lever again til there is a little fuel that runs out by the screwhead then tighten. Now start the engine. Crack that screwhead a bit after the motor is running to get any last bit of air out so the motor runs smoothly.

You also check the oil on the same side as you bleed the fuel line (the starboard side next to the sink). You will see the dipstick and it is self explanatory. Getting the oil out to change it requires starting the motor to warm the oil (it must be very warm/almost hot), putting the pump dipstick tube in the dipstick hole and suck out the oil. About a gallon. The oil filter is on the port side.There are spares behind the back of the port settee with the tools and spare parts.

The transmission oil check is on the transmission housing behind the motor. It is a yellow cap.Check the manual but I believe oil comes to the bottom of the dipstick, it is hard to check because the oil is very clean. It uses the same oil as the engine, Rotella-T 15w-40. No need to change it, just make sure it is at the proper level.

The Nigel Calder manual will spell out aything that you need to fix/investigate and there are all the supplies and tools you should need.
1 Comment

Replacement Portlights and Screens

3/27/2011

0 Comments

 
My 1985 Tartan 34-2 had factory screens for the portlights but they were lost by a PO.  After much hunting I found that the portlights and screens are available from Pompanette: the portlight is Bomar, part number N3414, and the screen is part number P3000-01.  The screens are hand-made @ $59.85 each.  The lead time is 2 weeks.

Pompanette also sells the right and left dogs P2000-68 (left) or P2000-69 (right) @ $17.00 each.  I asked about a gasket for the portlight and was told that it is only available on the ports with one seam in the aluminum frame.

The screens for the portlights for the 1985 T34-2 are installed with clips on the outside of the portlight.  While the portlights can not be closed with the screens installed. 

The 1986-89 models may have different portlights and screens.  Anyone have that information?
0 Comments

Welcome!

3/27/2011

88 Comments

 
This site is devoted to the Tartan 34-2 sailboat.  You are welcome to submit pictures of your T34-2, to make comments on the blog, to share maintenance and sailing tips useful to other T34-2 owners.  Jack
88 Comments

    Author

    Jack Harris is the owner of "Temptation," a 1985 Tartan 34-2.  Jack is a Professor of Sociology and an international consultant to local governments.  He sails out of Prinyer's Cove, Picton, Ontario, Canada.

    Archives

    August 2011
    March 2011

    Categories

    All
    Backstay Adjuster
    Bleeding Fuel Lines
    Diesel
    Hull Id
    Lazy Jacks
    Portlights
    Purchases
    Sail Twist
    Screens
    Strong Track
    Toerail
    Transmission
    Welcome

    RSS Feed

Powered by Create your own unique website with customizable templates.